Product Name
Small Steel Angles (Small L-Section / Light-Duty Angle Steel)
Introduction
Small Steel Angles are equal- or unequal-leg L-shaped steel sections used for light structural framing, bracing, trim, fixtures, racks, frames, supports and general fabrication. They provide a simple, low-cost way to add stiffness, create bolted/welded connections, make brackets and mountings, and are ideal where compact geometry and easy attachment are required.
Typical Materials & Grades
Mild / structural carbon steels: S235 / Q235 / A36 - common, easy to weld and economical.
Higher-strength (if needed): S355 / A572 Gr.50 - used when greater strength is required in the same footprint.
Stainless: 304 / 316 - for corrosion-sensitive environments.
Surface options: hot-dip galvanised, electro-galvanised, zinc spray, primer + paint, powder coat.
Special grades: weathering steel (Corten) or pre-hardened alloys on request.
Typical Sizes & Ranges
Leg lengths (equal L): 20 mm → 100 mm (typical small sizes: 20, 25, 30, 40, 50, 65, 75, 100 mm).
Unequal legs: e.g., 50 × 30 mm, 60 × 40 mm.
Thickness (t): 2.5 mm → 10 mm (common: 2.5, 3, 4, 5, 6, 8, 10 mm).
Lengths: standard 1 m, 2 m, 2.44 m (8 ft), 3 m, 6 m; cut-to-length available.
Mass estimator (steel): mass (kg/m) ≈ (a + b − t) × t × 0.00785
For equal-leg a×a×t, this reduces to mass ≈ (2a − t)·t·0.00785.
Quick Reference Example Table
| Size (mm) | Type | Area (mm²) approx. | Mass (kg/m) approx. |
|---|---|---|---|
| 25 × 25 × 3 | equal | (2×25−3)×3 = 141 mm² | 0.111 kg/m |
| 30 × 30 × 4 | equal | (60−4)×4 = 224 mm² | 1.76 kg/m* (note: check calc below) |
| 40 × 40 × 4 | equal | (80−4)×4 = 304 mm² | 2.39 kg/m |
| 50 × 50 × 5 | equal | (100−5)×5 = 475 mm² | 3.73 kg/m |
| 75 × 50 × 6 | unequal | (75+50−6)×6 = 714 mm² | 5.61 kg/m |
Note: use formula mass(kg/m) = area(mm²) × 0.00785. (Double-check arithmetic when preparing orders.)
Key Features & Benefits
Compact, economical members for light framing and bracing.
Easy to connect - flat faces for bolting, welding and tack attachments.
Good for retrofit & repair - simple to cut, drill and weld on site.
Available with corrosion protection - galvanising or coatings extend life outdoors.
Wide availability of standard small sizes for fast delivery.
Typical Applications
Light structural framing, shelving, racking and small gantries.
Brackets, angle cleats, corner guards and trim.
Small machine frames, supports and guide rails.
Guard rails, handrail supports, sign frames and fence brackets.
Reinforcement and patching in repair work.
Fabrication & Value-Added Services
Cut-to-length and end chamfering.
CNC punching / drilling of bolt patterns and slotted holes.
Notching / coping for clean corner fit-up.
Welding / assembles (pre-welded corner brackets, small subassemblies).
Bending / forming for light returns or tabs (limited by thickness).
Surface treatments: galvanize, powder coat, paint, primer.
Kitting & labelling: supply grouped installation kits with bolts/washers.
Dimensional Tolerances & Quality
Typical tolerances: follow mill standards - tighter tolerances available for cold-drawn/precision angles.
Surface & straightness: visually inspected; straightening available for critical uses.
Material certificates (MTC): available for structural orders on request.
Welding controls: WPS/PQR available for welded assemblies; NDT (MT/PT) as required on critical joints.
Corrosion Protection & Finishes
Hot-dip galvanising (HDG): recommended for outdoor use - long service life.
Electrogalvanised / zinc spray: lighter protection for indoor or mild environments.
Primer + topcoat / powder coat: aesthetic and corrosion protection for architectural uses.
Stainless supply: for high-corrosion or food/chemical environments where coatings are unsuitable.
Packaging & Logistics
Bundling: strapped bundles with timber or polymer spacers to prevent marking.
Protection: plastic end caps for coated items; VCI/oil for long-term storage.
Marking: size/length/qty labels on bundles for quick site identification.
Transport: short lengths fit standard logistics; for long runs consider splice planning.
How to Order - What We Need
When requesting a quote, please provide:
Size (leg1 × leg2 × thickness) and length(s) × quantity.
Material grade and required finish (mill / galvanized / painted / stainless).
Value-added processing (holes, slots, notches, welded assemblies).
Tolerance or flatness requirements if critical.
Certification needs (MTC, third-party inspection).
Delivery schedule and any transport or handling constraints.
Selection Tips
For light shelving, trims and brackets choose 2.5–4 mm thickness.
For small structural bracing or short spans choose 4–6 mm; add doublers at concentrated loads.
Use unequal legs when you need a wider bearing face on one side.
Choose stainless or HDG for outdoor/coastal exposure.
Where holes concentrate load, add local reinforcement plates to avoid tear-out and fatigue.
If you want, provide the specific size(s) and application and I'll:
calculate exact mass per metre and total weight for your quantity, and
recommend finish (galvanize/paint/stainless) and any necessary reinforcement or pre-drilling options for fast quoting.
Hot Tags: small steel angles, China small steel angles manufacturers, suppliers, factory





