Product Name
Transmission Flat Steel (Flat Bars for Power Transmission & Drive Systems)
Introduction
Transmission Flat Steel are rectangular flat bars specifically specified for power-transmission applications - coupling plates, conveyor straps, drive link plates, gear/shim plates, key/packing strips, and mounting plates used in power plants, substations, material-handling conveyors and drive assemblies. These flats are chosen for predictable cross-sectional strength, accurate bearing faces, good weldability and easy machining for holes, slots and keyways needed in transmission systems.
Typical Specifications
Forms: hot-rolled flat bar, cold-rolled flat strip, precision ground/planed flats, cut-to-length plates.
Common materials / grades: carbon steels (S235 / A36 / Q235), medium-carbon/alloy steels (C45 / 1045, 4140) for higher strength, stainless (304/316) for corrosion resistance, and spring/heat-treatable grades as required.
Widths (W): 20 mm – 1,200 mm (typical).
Thicknesses (T): 3 mm – 150 mm (thin link strips up to heavy mounting plates).
Lengths: cut-to-length (1–12 m typical) or single-piece to transport limits.
Tolerance / finish options: as-rolled, planed/ground for bearing faces, precision ground for tight thickness tolerances.
Mass formula (steel): mass (kg/m) = Width(mm) × Thickness(mm) × 0.00785.
Key Features & Advantages
Accurate bearing surface: planed or ground faces ensure full-contact for couplings, bearings and shims.
Good machinability & weldability: suitable for drilling, milling, slotting, welding and forming required by transmission assemblies.
Wide material choices: from low-cost mild steels to heat-treatable alloy and stainless grades to match strength, wear and corrosion requirements.
Customizable: pre-drilled holes, slots, machined keyways, countersinks and edge chamfers supplied to print.
Consistent geometry: predictable cross-section simplifies stress calculations and fitting for drive components.
Coating & protection: available hot-dip galvanized, coated, or oiled/VCI-wrapped for storage and transport.
Typical Applications
Coupling plates, flange plates and connection straps for gearboxes and drives.
Conveyor chain plates, link strips and tensioning straps.
Bearing/shim plates and packing strips for alignment and wear control.
Mounting plates, baseplates and motor foot plates.
Gasket backing strips, wear liners and splice/cover plates in transmission housings.
Repair strips and retrofit reinforcement plates for worn components.
Fabrication & Value-Added Services
Cut-to-length & sawing: precision length cutting to reduce onsite coping.
CNC machining: holes, slots, counterbores, keyways, milled pockets and profile trimming.
Precision grinding & planing: flatness and thickness control for bearing and shim applications.
Weld & assembly: pre-welded brackets, welded studs, tack-assembled kits and jigged sub-assemblies.
Heat treatment: supplied annealed, normalized, quenched & tempered or case-hardened where wear resistance or strength is required.
Surface treatments: shot-blast & primer, hot-dip galvanize, phosphate, painting or VCI oil for export.
Kitting: numbered assembly kits with bolts/fasteners and installation notes for production lines.
Quality Assurance & Testing
Material certification: Mill Test Certificate (MTC) and full traceability on request.
Dimensional inspection: width, thickness, flatness and length checks; runout and parallelism for ground faces.
Mechanical testing: tensile, yield and hardness testing per grade/contract.
NDT: PT/MT or UT available on welded assemblies or critical components.
Surface inspection: finish, coating thickness and adhesion testing if required.
Packaging & Delivery
Bundling: strapped bundles with polymer/timber spacers to avoid marking for flat bars.
Protection: VCI or oil film for short-term corrosion protection; wooden crates for precision-ground plates.
Marking: size, grade, heat number and PO/part ID.
Logistics: single-piece lengths sized to transport/crane limits or supplied as spliced kits for long runs.
Lead time: stock sizes typically short; custom machining, heat treatment or coated orders depend on scope (quote will state lead time).
Ordering Information - What We Need
Please provide:
Width × thickness × length and quantity (or full drawings).
Material grade and required supply condition (as-rolled / planed / ground / heat-treated).
Tolerances and flatness requirements for bearing faces.
Value-added requests: holes, slots, countersinks, keyways, weld studs, preassembly.
Coating/packaging preference (galvanize, primer, VCI oil).
Any required testing/certification (MTC, tensile, hardness, NDT) and delivery deadline.
Why Choose Our Transmission Flat Steel?
We supply transmission-grade flats with precision flatness, suitable metallurgy and shop-ready machining so components fit and perform from first assembly. Whether you need simple coupling straps or precision bearing shims and heat-treated mounting plates, we offer material selection, machining, heat-treatment and QA services to deliver ready-to-install parts that reduce field work and improve system reliability.
If you like, give me a size list (width × thickness × qty) or a sample part drawing and I'll prepare a size-to-weight table, machining allowance suggestions and a quick quotation outline.
Hot Tags: transmission flat steel, China transmission flat steel manufacturers, suppliers, factory





